--- title: "Film shooting, developing & scanning FAQ | Neo Analog Lab" url: https://shop.neoanaloglab.com/en/faq language: en description: "RAW vs JPG, the orange mask, scan resolution, and other common questions about film photography and digitization — answered by Neo Analog Lab." --- FAQ # Film shooting, developing & scanning FAQ RAW vs JPG, the orange mask, scan resolution, and other common questions about film photography and digitization — answered by Neo Analog Lab. Q ## How do you hold 38°C for C-41 development at home? **There are two answers: hold the chemistry at 38°C, or add time to make up for the drift.** C-41's standard temperature is 38°C and the developer step is around 3 minutes 15 seconds. Because the step is short, a one-degree error matters — this is where home colour development usually goes wrong. **Option 1: hold the temperature.** Sit the bottles in a tub of 40–43°C water, wait until they read 38°C, and start. In winter the bath cools during the run, so you top it up. Plenty of people repurpose a sous-vide cooker or an aquarium thermostat; anything that controls to 0.5°C works. **Option 2: compensate with time.** Warm the chemistry roughly, and when the temperature drifts during processing, extend the development time to match. The [AGO Film Processor](https://shop.neoanaloglab.com/en/products/ago-film-processor) works this way, which removes the need for a temperature-holding device at all. Note that **time compensation only runs in rotary (horizontal) mode** — stood upright for stick agitation, the temperature probe is not in the liquid, so compensation switches off. A lower-temperature process around 30°C also exists, but fewer kits support it. For what it's worth, C-41 is only three steps — colour developer, blix, stabiliser — so once temperature is solved it is simpler than black-and-white. [Read more →](https://shop.neoanaloglab.com/en/news/faq-color-home-development-temperature) Q ## What is the AGO Film Processor, and how can it work without controlling temperature? **The AGO Film Processor is a battery-powered agitator that grips a Paterson Super System 4 tank and turns it.** It is designed and built by Vintage Visual OÜ in Estonia. It gets consistent results without a heater because it **replaces temperature control with time compensation**. A sensor watches the chemistry during the run and extends development time to match any drop (Active Time-Compensation). You warm the chemistry roughly, pick a program, and press start. - Processes: B&W, C-41, E-6, ECN-2 and RA-4, with separate programs per chemistry brand, added over Wi-Fi - Agitation: rotary (horizontal) and stick (vertical). **Time compensation only runs in rotary mode** - Chemistry: rotary processing uses up to 60% less than traditional vertical or inversion agitation - Body: 88 × 136 × 170 mm, 556 g, IP56, two 18650 Li-ion cells giving 4–5 hours of continuous use, USB-C charging No darkroom is needed — only a changing bag for loading film onto the reels. Sources: [AGO Film Processor product page](https://vintagevisual.eu/pages/ago-film-processor/) , [AGO wiki](https://www.vintagevisual.eu/wiki/ago-wiki/machine-overview/) [Read more →](https://shop.neoanaloglab.com/en/news/faq-what-is-ago-film-processor) Q ## Does the AGO work with a Paterson tank I already own? **Yes. AGO works with the whole Paterson Super System 4 range, PTP114 through PTP118.** One modification is required: the **funnel needs three holes drilled into its side** so chemistry can be introduced. Vintage Visual supplies a drilling template with every processor, and also sells a [pre-modified funnel and rear stand kit](https://shop.neoanaloglab.com/en/products/ago-modified-funnel-rear-stand-kit) if you would rather not drill. Each additional tank needs its own funnel. Minimum chemistry volumes per tank, as published by the manufacturer: | Tank | 110/135/120/220/127 | 4×5 / 9×12cm | 5×7 | Paper 5 (8×10) | | --- | --- | --- | --- | --- | | 1-reel PTP114 | 250ml | — | — | — | | 2-reel PTP115 | 350ml | — | — | — | | 3-reel PTP116 | 450ml | 350ml | — | — | | 5-reel PTP117 | 650ml | 500ml | 350ml | 250ml | | 8-reel PTP118 | 950ml | 750ml | 500ml | 400ml | One to eight rolls per run, depending on the tank. Older Paterson tank systems and other makes such as Jobo or AP are not supported. If you already own tanks, the [processor on its own](https://shop.neoanaloglab.com/en/products/ago-film-processor-without-tank) is the one to get; starting from scratch, the [complete set with tank](https://shop.neoanaloglab.com/en/products/ago-film-processor) includes the tank and reels. [Read more →](https://shop.neoanaloglab.com/en/news/faq-ago-paterson-tank-compatibility) Q ## How much chemistry does rotary processing actually save? **Up to 60%, according to the manufacturer.** Inversion agitation needs enough liquid to cover the film completely; roll the tank on its side and a shallow pool reaches every part of the reel as it turns. In real numbers, a two-reel Paterson PTP115 needs **350ml per step**. Mix one litre of a C-41 kit and that is two rolls several times over. | Tank | Rotary volume (135/120) | | --- | --- | | 1-reel PTP114 | 250ml | | 2-reel PTP115 | 350ml | | 3-reel PTP116 | 450ml | | 5-reel PTP117 | 650ml | | 8-reel PTP118 | 950ml | Less chemistry also means less waste to dispose of. C-41 and E-6 kits have a limited life once mixed, so being able to work in small volumes is a real saving rather than a theoretical one. The [AGO Film Processor](https://shop.neoanaloglab.com/en/products/ago-film-processor) supports both rotary and stick agitation, but the chemistry saving and time compensation both apply in rotary mode. [Read more →](https://shop.neoanaloglab.com/en/news/faq-rotary-processing-chemistry-saving) Q ## Can the AGO handle 4×5, Super 8 and RA-4 prints? **Yes. Each format is handled by adding its own reel.** The included tank and reels cover 135 and 120. 127 and 220 also load onto the standard Paterson reels. Everything else needs a dedicated reel. | Format | Reel | Tank needed | | --- | --- | --- | | 110 | [REEL 110](https://shop.neoanaloglab.com/en/products/ago-reel-110) | any tank | | 4×5 | [REEL 4x5](https://shop.neoanaloglab.com/en/products/ago-reel-4x5) | PTP116 or larger | | 9×12cm | [REEL 9x12](https://shop.neoanaloglab.com/en/products/ago-reel-9x12) | PTP116 or larger | | 5×7 | [REEL 5x7](https://shop.neoanaloglab.com/en/products/ago-reel-5x7) | PTP117 or larger | | 8×10 | [REEL Paper 5](https://shop.neoanaloglab.com/en/products/ago-reel-paper-5) | PTP117 or larger | | Super 8 cine film | [REEL Super 8](https://shop.neoanaloglab.com/en/products/ago-reel-super-8) | — | | RA-4 colour prints | REEL Paper 5 / [REEL Paper 8](https://shop.neoanaloglab.com/en/products/ago-reel-paper-8) (to 30×40cm) | PTP117 or larger | RA-4 support means **you can process colour prints without owning a darkroom drum**. Not many home machines cover that much ground. If you want both 5×7 and Paper 5, the [bundle](https://shop.neoanaloglab.com/en/products/ago-reel-5x7-paper-5-set) costs less than buying them separately. [Read more →](https://shop.neoanaloglab.com/en/news/faq-ago-large-format-super8-ra4) Q ## Why do my scans look grainy or color-shifted? **Grain** is intrinsic to film, but it becomes prominent with: high-ISO stocks (800+), push processing, and above all **underexposure**. When a thin negative is brightened during scanning, shadow grain blows up. If a roll looks "rougher than expected," underexposure is the usual culprit. **Color shifts** typically come from: (1) expired or heat-damaged film, (2) underexposure (negatives store little color information in the shadows), (3) unusual light sources (fluorescent, mixed light). The classic case: tungsten-balanced cinema film (500T) shot in daylight without a filter goes blue. We adjust color and density frame by frame, but no scan can recover information the negative never recorded. **"When in doubt, overexpose negatives slightly"** is the single best rule for clean scans. ## Sources - [Kodak VISION3 500T technical data sheet](https://www.kodak.com/content/products-brochures/Film/VISION3_5219_7219_Technical-data.pdf) - [ILFORD's official guide to film speed and grain](https://www.ilfordphoto.com/choosing-your-first-ilford-film/) - [Kodak's GOLD 200 exposure latitude specifications](https://www.kodak.com/en/still-film/product/consumer/gold-200-film/) [Read more →](https://shop.neoanaloglab.com/en/news/faq-grain-color-shift) Q ## What is the difference between negative and reversal (slide) film? **Negative film** records the image with tones inverted (color negatives add the orange mask on top). You only see the final picture after printing or scanning inverts it back. Its greatest strength is **exposure latitude**: a stop or two of error is recoverable, which makes it ideal for beginners. **Reversal (slide) film** develops directly into a positive. On a light table, the transparency and color intensity are unlike anything else. But the **exposure latitude is razor thin** (about ±0.5 stop), demanding accurate metering and technique. Starting out? Shoot color negative (C41). Once your exposure is confident, treat yourself to the E6 reversal experience. ## Sources - [Kodak's Gold 200 technical data sheet (E-7022)](https://www.kodakprofessional.com/sites/default/files/wysiwyg/pro/resources/E7022%20Gold%20tech%20sheet.pdf) - [Fujifilm's Professional Film Data Guide](https://asset.fujifilm.com/www/ca/files/2020-03/d52487c5c6f84e7f935c299491c5c1ff/ProfessionalFilmDataGuide.pdf) - [Kodak's EKTACHROME color reversal processing manual](https://www.kodak.com/content/products-brochures/Film/Processing-KODAK-Motion-Picture-Films-Module-11.pdf) [Read more →](https://shop.neoanaloglab.com/en/news/faq-negative-vs-reversal) Q ## Will airport X-rays fog my film? **Traditional carry-on X-ray machines**: film ISO 800 and slower rarely shows visible damage after a few passes - but damage accumulates, so be careful on multi-leg trips. **CT scanners** (the newer machines rolling out worldwide) use far stronger doses and **can fog film with stripe patterns in a single pass**. **Checked-baggage X-rays are the strongest of all - never put film in checked luggage.** Best practice: carry all film in a clear plastic bag and **ask for a hand inspection** at security. Most airports will accommodate: "Film, hand check please." ## Sources - [TSA's official guidance on traveling with photographic film](https://www.tsa.gov/travel/security-screening/whatcanibring/items/film) - [Kodak's advisory on CT scanning X-ray technology and film](https://kodakprofessional.com/photographers/resources/ct-scanning-x-ray-technology-and-film) - [ILFORD (HARMAN) advice on airport X-ray scanners and film](https://harmanlab.com/pages/advice-on-airport-x-ray-scanners) [Read more →](https://shop.neoanaloglab.com/en/news/faq-xray) Q ## How should I store film? Can I still shoot expired film? **Unused film** hates heat and humidity. Refrigerate rolls you will use within months; freeze anything you are keeping for years. Let film warm up for 2-3 hours before opening to avoid condensation. **Exposed film**: the latent image fades over time, so **develop your shot rolls promptly**. **Expired film** is shootable, but expect lower effective speed, more base fog, and color shifts. The classic rule of thumb: add one stop of exposure for every decade past expiry. The unpredictability is part of the charm - but for important occasions, shoot in-date film. ## Sources - [Kodak's technical publication Storage and Care of KODAK Photographic Materials (E-30)](https://kodakprofessional.com/sites/default/files/wysiwyg/pro/CIS_E30.pdf) - [Fujifilm's film data sheet on unprocessed film handling and storage](https://asset.fujifilm.com/www/us/files/2022-02/f4606a5c43dacb389a1d9eb35e0b18db/fujifilm-200-speed-film_data-sheet.pdf) - [ILFORD's official film FAQ](https://www.ilfordphoto.com/faqs/ilford-film-faqs/) [Read more →](https://shop.neoanaloglab.com/en/news/faq-film-storage) Q ## Can I get already-developed film scanned only? Absolutely. On the processing order page, choose the **"Scan only (developed film)"** button for each roll. Since no development is involved, you only pay for the scanning. Great for: - Digitizing old negatives and slides found at home - High-quality scans of film developed elsewhere or self-developed - Re-scanning rolls that were only scanned at low resolution before Cut, sleeved film strips are fine to send as-is. After scanning, your film is **always returned** (return shipping is included in the price). For older film with mold or strong curl, we will handle it as carefully as we can - just mention it in the order notes. ## Sources - [Kodak's official film storage and handling guidance](https://www.kodak.com/en/motion/page/storage-information/) - [the National Film Preservation Foundation's storage guidance](https://www.filmpreservation.org/preservation-basics/good-storage-practices) - [the Image Permanence Institute's Visual Decay Guide](https://www.filmcare.org/visual_decay) [Read more →](https://shop.neoanaloglab.com/en/news/faq-scan-only) Q ## What is the difference between C41, E6, B&W, and ECN-2 processing? Which does my film need? **C41**: the standard process for color negative film - Kodak Gold, Portra, Fujifilm color negatives. **E6**: for reversal (slide) film, which develops into a positive you can view directly on a light table - Ektachrome, Provia, Velvia. **B&W**: black-and-white negative development - HP5 Plus, Tri-X, Delta, ACROS. B&W reversal is a separate, special process. **ECN-2**: for cinema color negative stocks like Kodak VISION3 (500T, 250D). The chemistry differs from C41 and the remjet backing must be removed. When in doubt, check the box or cassette for "Process C-41" / "E-6" markings - or just write the film name in the order notes and we will identify it for you. ## Sources - [Kodak VISION3 500T technical data sheet (Process ECN-2, rem-jet backing)](https://www.kodak.com/content/products-brochures/Film/VISION3_5219_7219_Technical-data.pdf) - [ILFORD's official black & white reversal processing guide](https://www.ilfordphoto.com/reversal-processing/) - [Kodak EKTACHROME E100 product page (E-6 process)](https://www.kodak.com/en/still-film/product/professional/ektachrome-e100-film/) [Read more →](https://shop.neoanaloglab.com/en/news/faq-c41-e6-bw) Q ## What are push and pull development? **Push development** extends the development time for film exposed above its box speed - for example ISO 400 film shot at 1600 in low light is "pushed 2 stops." Expect stronger contrast and more pronounced grain; many photographers love the look. **Pull development** is the opposite: shortened development for film that was overexposed (shot below box speed). When ordering, tell us the difference in stops between the ISO you actually set and the film's box speed. Push/pull applies to the whole roll, so **you cannot change ISO mid-roll**. We support ±1-5 stops. ## Sources - [Kodak's Tri-X technical data sheet (F-4017)](https://business.kodakmoments.com/sites/default/files/files/resources/f4017_TriX.pdf) - [ILFORD's official guide to processing black & white film](https://www.ilfordphoto.com/wp/wp-content/uploads/2017/04/Processing-your-first-black-and-white-film.pdf) - [ISO 6:1993 film speed standard](https://www.iso.org/standard/3580.html) [Read more →](https://shop.neoanaloglab.com/en/news/faq-push-pull) Q ## How do I choose a scan resolution (10MP / 24MP / 60MP)? **10MP**: plenty for viewing on phones and computers and for social media. Small, easy-to-manage files - great if you mostly shoot for the record. **24MP**: comfortably supports A4-A3 prints and is the best-balanced choice. When in doubt, pick this. **60MP**: maximum quality for large prints, aggressive cropping, or archival purposes - it records the film grain itself. Especially worthwhile for 120 (medium format), which holds more detail than 135 to begin with. One caveat: higher scan resolution cannot invent detail that was never captured on the film. Work backwards from how you plan to use the images. ## Sources - [Kodak T-MAX 100 technical data sheet (F-4016, resolving power up to 200 lines/mm)](https://www.kodakprofessional.com/sites/default/files/wysiwyg/pro/resources/f4016_TMax_100.pdf) - [Kodak Portra 400 technical data sheet (E-4050)](https://kodakprofessional.com/sites/default/files/2025-07/e4050.pdf) - [Epson's recommended print resolution guidance (300–360 dpi)](https://www.epson.co.uk/en_GB/faq/KA-01467/contents?loc=en-us) [Read more →](https://shop.neoanaloglab.com/en/news/faq-scan-resolution) Q ## What is the orange mask on color negative film, and why is it removed when digitizing? Hold a color negative up to the light and the whole strip looks orange. That is the **orange mask** - not dirt or age, but part of the film's design. Color dyes are inherently imperfect, so manufacturers build an orange corrective layer into the emulsion. In the darkroom era this mask is what made accurate color printing possible. When digitizing, simply inverting an orange-tinted negative produces a heavy blue-cyan cast. Scanning therefore has to **measure and cancel the mask first, then invert the tones** to recover the real color balance - this step is what "mask removal" means. Our scans measure the base color of every roll individually, remove it, and then fine-tune the palette to the character of each film stock. The same negative can look dramatically different depending on how well the mask removal is done. ## Sources - [Kodak's technical guide "Exploring the Color Image" (Masking by Colored Couplers, pp. 40–43)](https://www.kodak.com/content/products-brochures/Film/Exploring-the-Color-Image.pdf) - [Kodak's "The Essential Reference Guide for Filmmakers"](https://www.kodak.com/content/products-brochures/Film/kodak-essential-reference-guide-for-filmmakers.pdf) [Read more →](https://shop.neoanaloglab.com/en/news/faq-orange-mask) Q ## What is the difference between RAW and JPG scans? Which should I choose? **JPG** files are finished images: we remove the orange mask (for negatives) and grade every frame. They open anywhere and are instantly ready for sharing or printing. For most customers JPG is the right choice. **RAW** (our scanners output DNG) is the **scanner's raw data with no mask removal and no grading applied**. A color-negative RAW opens as an orange negative image - you invert, remove the mask, and grade it yourself in Lightroom + Negative Lab Pro or similar. Maximum control, but it requires post-processing skills and time, and files are several times larger. **Not sure?** For everyday shooting, JPG. If you want full control over the final look, RAW+JPG gives you both: browse the roll in JPG, then finish your favorite frames from RAW. ## Sources - [Negative Lab Pro, a Lightroom plugin for negative conversion](https://www.negativelabpro.com/) [Read more →](https://shop.neoanaloglab.com/en/news/faq-raw-vs-jpg) [Order developing & scanning](https://shop.neoanaloglab.com/en/processing) [Still stuck? Contact us →](https://shop.neoanaloglab.com/en/contact)